The OPA342 is a single, 5.5V, 1MHz, low bias current (0.2pA), RRIO op amp

The OPA342 family of rail-to-rail CMOS operational amplifiers are designed for low cost, low power, miniature applications. They are optimized to operate on a single supply as low as 2.5V, with an input common-mode voltage range of 300mV beyond the supply

The AFE3010 is a ground fault circuit interrupter (GFCI) controller with self-test and neutral ground fault detection

The AFE3010 is a precision, low power, AM3352BZCZ100 ground fault circuit interrupter (GFCI) controller for detecting ground fault leakage paths in electrical circuits. The device is a single IC solution that continuously monitors a circuit for multiple f

The LMP7312 is a single, 5.5V, 1MHz operational amplifier

The LMP7312 is an AD260BND-5 digitally programmable variable gain amplifier/attenuator. Its wide input voltage range and excellent accuracy make it the first choice for applications requiring high precision, such as data acquisition systems for IO modules

The OPA1602 is a dual, SoundPlus high performance, bipolar input audio operational amplifier

The OPA1602 and OPA1604 bipolar input op amps achieve a very low 2.5nV/√Hz noise density with ultra-low distortion of 0.00003% at 1kHz. The OPA1602 and OPA1604 series of ADNS-2030 op amps provide rail-to-rail output swing within 600mV into a 2k&Ome

LM3421 is an N-channel controller for constant current LED driver with series DIM FET driver

The LM3421 and LM3423 family of devices are versatile high voltage N-channel MOSFET controllers for LED drivers. They can be easily configured for buck, boost, buck-boost and SEPIC topologies. This flexibility, along with a rated input voltage of 75 V, ma

The TPS22998 is a 5.5V, 10A, 4mΩ on-resistance load switch

The TPS22998 is an AOD454A single-channel load switch that provides a configurable rise time to minimize inrush current. The device contains an N-channel MOSFET that operates over an input voltage range of 0.2 V to 5.5 V and supports up to 10 A continuous

The DRV425-Q1 is an automotive, fully integrated fluxgate magnetic sensor

Designed for uniaxial magnetic field sensing applications, the DRV425-Q1 automotive device enables galvanic isolation, high sensitivity, and accurate DC and AC field measurements. The device offers a unique and proprietary integrated fluxgate sensor (IFG)

The THS770012 is a high-speed fully differential ADC driver amplifier with 10 to 13 dB selectable gain

The THS770012 is a wideband ADM812RART-REEL7 fully differential amplifier with an adjustable gain range of +10dB to +13.7dB (using external components). It is designed and optimized for driving 16-bit analog-to-digital converters (ADCs) with input frequen

The TLC271B is a single, 16V, 2MHz, 2mV offset, In to V- op amp

The TLC271 op amp combines various input offset voltage levels with low offset voltage drift and high input impedance. Additionally, the TLC271 offers a bias selection mode that allows the user to select the best combination of power consumption and AC pe

The OPA4863 is a Quad, Low Power, 110MHz, RRIO Voltage Feedback Amplifier

The OPA4863 device is a low-power, unity-gain stable, rail-to-rail input and output, AD5390BCPZ-5 voltage feedback operational amplifier designed to operate from a 2.7V to 12.6V supply range. Consuming only 700µA per channel, the OPA4863 device offe

The TMUX7236 is a 44V, low RON, 2:1 (SPDT), two-channel precision switch with latch-up immunity and 1.8V logic

The TMUX7236 is an AZ431LBKTR-E1 complementary metal-oxide-semiconductor (CMOS) switch that is latch-up resistant in a dual 2:1 configuration. The device is suitable for dual supply (±5 V to ±22 V), single supply (5 V to 44 V), or asymmetric

The AMC1306M05-Q1 is an automotive, ±50mV input, precision reinforced isolation modulator with CMOS interface

The AMC1306M05-Q1 is an AD5390BSTZ-3 precision delta-sigma (ΔΣ) modulator whose output is separated from the input circuit by an isolation barrier that is highly resistant to magnetic interference. The barrier is certified to provide reinforce

The SN6505A is a low noise, 1A, 160kHz transformer driver with soft-start for isolated power supplies

The SN6505A is a low noise, low EMI push-pull transformer AP8800FNG-7 driver designed for small form factor isolated power supplies. It can drive a 2.25 V to 5 V DC power supply. Ultra-low noise and EMI are achieved through slew rate control of the output

The LM25180 is a 42Vin Opticless Flyback Converter with 65V, 1.5A Integrated MOSFET

The LM25180 is a primary-side regulated (PSR) flyback converter with high efficiency over a wide input voltage range of 4.5V to 42V. The isolated output voltage is sampled from the primary-side flyback voltage without the need for an optocoupler, voltage

The TPS2116 is a 1.6V to 5.5V, 40mΩ, 2.5A, Low IQ, Priority Power Multiplexer

The TPS2116 is an AP2127K-ADJTRG1 power multiplexer device rated from 1.6V to 5.5V with a maximum current rating of 2.5A. The device uses N-channel MOSFETs to switch between supplies while providing a controlled slew rate when voltage is first applied.Due

The INA4290 is a quad, 110V, high voltage, high bandwidth, unidirectional current sense amplifier

The INA4290is an ADUC7027BSTZ62 ultra-precision current sense amplifier that measures the voltage drop across a shunt resistor over a wide common-mode range of 2.7 V to 120 V. - Low offset voltage of ±12 μV (max), small gain error of ±0.1

The DAC61402 is a dual, 12-bit, ±20V range, buffered output DAC with precision internal reference

The 16-bit DAC81402 and 12-bit DAC81402 (DAC81402) are pin-compatible, dual-channel, buffered, high-voltage output, AD7894AR-10 digital-to-analog converters (DACs). These devices include a low-drift 2.5V internal reference, eliminating the need for an ext

The TL071H is a single-channel low input bias current standard operational amplifier

TL071H, TL072H product parameters, documentation and supply information TL072H and TL074H product parameters, documentation and supply information" TL074H) series devices are the industry standard devices. These AQV212S devices offer excellent value for c

The LMH9235 is a 3.3 GHz to 4.2 GHz single-ended to differential amplifier with integrated balun

The LMH9235 device is a high performance, single-channel, single-ended input to differential output receive RF gain block AD8056ARM amplifier supporting the 3.6 GHz center band. The device is ideal for supporting the requirements of next-generation 5G AAS

The TMAG5123 is a high voltage (up to 38V), planar high precision switch

The TMAG5123 is a chopper-stabilized omnipolar, low-level, in-plane, Hall-effect switching sensor. The TMAG5123 simplifies the mechanical placement of the AD1584ART-REEL7 sensor by measuring the magnetic field parallel to the surface of the printed circui

Page 1 / 17